Congratulations!

You have found it! As a small gift, you will receive the following voucher code for redemption in our shop:


This voucher grants a discount of €0.00

The article was successfully added.

Tuning cylinder kit RS634 (S50/4-channel with 63ccm) - revised version

Tuning cylinder kit RS634 (S50/4-channel with 63ccm) - revised version

€309.30
incl. VAT.5, incl. Shipping

Immediately available

DHL standard shipping2:
Delivery time: 1 - 4 workdays.
DHL Express shipping3 (subject to surcharge):
Heute bis 14:30 Uhr per Express bestellen, garantierte Lieferung Freitag, den 26.04.20242.
  • New
  • RZT
  • 10005804
  • 4052309054907
  • Modification acceptance required
  • In case of complaints, please note that the installation certificate of a specialist workshop is urgently required.
    The manufacturer requires this proof in the event of a complaint in order to be able to exclude installation errors during assembly.

Maik / 7 Aug 2019
Hervorragender Kit für S50 - 108 km/h - gemessen mit GPS. AOA3 Vario und RZT RVFK 21CS sind Bedingung damit die Leistung von diesem Zylinder richtig ausgenutzt...

Article characteristics

passend für Fahrzeugtyp: S50
Baugruppe: Motor & -teile
passend für Fahrzeughersteller: Simson
Shipping weight: 2,374 kg

Description

So far we have always concentrated on the newer engine variants of the S51 in our cylinder kits.
The problem is the inherently low torque, as the engine is still very short-stroke. With all
tuned 50ccm kits there is always a rather "weak-chested" engine with a lot of speed.

The second version was the widely used reaming of the cylinder with a S70 piston. This should increase the torque to 63ccm, but most of it will be "eaten up" by a much too long intake timing of almost 200° (because the S70 piston

is

10mm shorter

than the original piston). Furthermore these motors are very difficult to tune.

Out of this emergency we have finally built a kit that doesn't have these disadvantages!

The

basis

is a specially made 45mm piston with all the advantages of our well-known kit pistons.

This finally gives us the opportunity to build an inexpensive kit that combines good peak performance with a decent rev range

(this is especially important for engines that usually only have a three-speed gearbox). As

always, the scope of delivery

includes cylinder with complete piston, cylinder head, gaskets and assembly instructions.

The kits fit any S50 engine.

The

kits can also be based on the round Schwalbe- or Star- cylinder, but a usable

cylinder with head (clean, technically OK) must be sent in. Scope of delivery cylinder kit: - cylinder- cylinder head- piston (barikit)- pin- safety clips- gasket- installation instructions - inlet approx. 21mm-
suitable to it (as piston 1st oversize): article
no.: 10016502Please note
:For engine or cylinder conversions or - regenerations the control times must be checked and adjusted if necessary
.

Notes

Use in public road traffic will invalidate the operating permit of your vehicle! It may be possible to obtain an individual approval for registration in the vehicle documents.

Customer reviews

Rate the purchased item now and get up to 170 AKF bonus points. In the menu item Reviews menu item in your customer account, you will find all the items for which you can submit a rating.
Quality
15 Reviews
Accuracy of fit
15 Reviews
Price / Performance
15 Reviews
Expectations met
15 Reviews
Recommendation
15 Reviews
(15)
Average rating:
∅ 4.84 being based on 15 Reviews
  • 5 Stars
    (14)
  • 4 Stars
    (0)
  • 3 Stars
    (1)
  • 2 Stars
    (0)
  • 1 Stars
    (0)

Click to filter

(Model: S50)

Kanäle ordentlich reinigen vor dem Einbau. Am besten gleich neue Vibrationsdämpfer mitbestellen.

(Model: S50)

(Model: S50)

(Model: S50)

(Model: S50)

(Model: Not specified)

(Model: Not specified)

(Model: Not specified)

(Model: Not specified)

(Model: Not specified)

(Model: Not specified)

Show more reviews